2013年1月5日土曜日

NEC IX2105でAmazon VPCにVPN接続する

UNIVERGE IX2000/IX3000シリーズ : UNIVERGE IX2105 | NECをお借りしたので、VPCに対してVPN接続してみた。

結果から言うと

  • あっさりつながる
  • 小さい
  • (ふんでも)壊れにくそう
  • (消費電力が小さいので)熱くならない。静か。

というのは間違いなさそう。十分に速い線がないので、パフォーマンスについては言及できません。






 

準備として、VPCをつくって、Customerゲートウェイを作成するまでをAWSのマネージメントコンソールで行います。

  1. AWS Management ConsoleのVPCページを開ける
  2. ”Start VPC Wizard”ボタンを押して作成開始
  3. “VPC with a Private Subnet Only and Hardware VPN Access”シナリオを選択
  4. IX2105につけるIPアドレスをいれる
  5. “Use dynamic routing (requires BGP)”を選択してVPCを作成
  6. VPN CONNECTIONS->VPN Connectionsから、作成されたVPN接続の設 定ファイルをダウンロードする。ベンダのところには対応していないのでGenericを入手する。

すると、以下のようなファイルが入手できているはず。とりあえず、vpn-ix2105.txtとでもしておきます。


Amazon Web Services
Virtual Private Cloud

VPN Connection Configuration
================================================================================
AWS utilizes unique identifiers to manipulate the configuration of
a VPN Connection. Each VPN Connection is assigned a VPN Connection Identifier
and is associated with two other identifiers, namely the
Customer Gateway Identifier and the Virtual Private Gateway Identifier.

(以下続く)

ファイルをひとつひとつ見てもいいのですが、さきに入れるべき情報を整理します。

IPSecで使う鍵の入手


$ grep '\-\ Pre-Shared Key' vpn-ix2105.txt
- Pre-Shared Key : トンネル1の鍵
- Pre-Shared Key : トンネル2の鍵

設定に必要なAWS側のIPアドレスの入手


$ grep "\-\ Virtual\ Private\ Gateway" vpn-ix2105.txt
- Virtual Private Gateway : 27.0.1.16
- Virtual Private Gateway : 169.254.252.25/30
- Virtual Private Gateway : 27.0.1.144
- Virtual Private Gateway : 169.254.252.29/30

$ grep "\-\ Customer\ Gateway" vpn-ix2105.txt
- Customer Gateway : IX2105につけるIPアドレス
- Customer Gateway : 169.254.252.26/30
- Customer Gateway ASN : 65000
- Customer Gateway : IX2105につけるIPアドレス
- Customer Gateway : 169.254.252.30/30
- Customer Gateway ASN : 65000

ここまで整理したら、IX2105にシリアルコンソールを挿して設定です。

まずは初期化してしまいましょう。


Router#
Router# configure
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)# erase startup-config
Are you sure you want to erase the startup-configuration? (Yes or [No]): yes
Router(config)# exit
Router# default-console command-line
% You must RELOAD the router for this configuration to take effect.
Router#

初期化後の設定はごちゃごちゃ解説するよりそのもの貼ったほうがわかりやすいので
はっておきます!Good luck!


!
timezone +09 00
!
logging buffered 131072
logging subsystem all warn
logging timestamp datetime
!
!
ip ufs-cache enable
ip route default GigaEthernet0.1
ip access-list sec-list permit ip src any dest any
!
!
!
ike proposal ike-prop encryption aes hash sha group 1024-bit
!
ike policy ike-policy1 peer 27.0.1.16 key bbbbbbaaaaaaaaaaaaamavO8waikpkWlL ike-prop
ike keepalive ike-policy1 10 3
!
ike policy ike-policy2 peer 27.0.1.144 key cccccccccdddddddddddddda49yt ike-prop
ike keepalive ike-policy2 10 3
!
ipsec autokey-proposal ipsec-prop esp-aes esp-sha lifetime time 3600
!
ipsec autokey-map ipsec-map1 sec-list peer 27.0.1.16 ipsec-prop pfs 1024-bit
!
ipsec autokey-map ipsec-map2 sec-list peer 27.0.1.144 ipsec-prop pfs 1024-bit
!
ppp profile pppoe
authentication myname aa@bb.jp
authentication password aa@bb.jp xxxxxxxxxxxxxxxxx
!
router bgp 65000
neighbor 169.254.252.25 remote-as 10124
neighbor 169.254.252.25 timers 10 30
neighbor 169.254.252.25 receive-capability override
neighbor 169.254.252.29 remote-as 10124
neighbor 169.254.252.29 timers 10 30
neighbor 169.254.252.29 receive-capability override
address-family ipv4 unicast
originate-default always
!
device GigaEthernet0
!
device GigaEthernet1
!
interface GigaEthernet0.0
no ip address
shutdown
!
interface GigaEthernet1.0
description == admin net ==
ip address 192.168.1.205/24
no shutdown
!
interface GigaEthernet0.1
description == flets ==
encapsulation pppoe
auto-connect
ppp binding pppoe
ip address ipcp
ip napt enable
ip napt static GigaEthernet0.1 udp 500
ip napt static GigaEthernet0.1 50
no shutdown
!
interface Loopback0.0
no ip address
!
interface Null0.0
no ip address
!
interface Tunnel0.0
description == Tunnel 1 ==
tunnel mode ipsec
ip address 169.254.252.26/30
ip tcp adjust-mss auto
ipsec policy tunnel ipsec-map1 out
no shutdown
!
interface Tunnel1.0
description == Tunnel #2 ==
tunnel mode ipsec
ip address 169.254.252.30/30
ip tcp adjust-mss auto
ipsec policy tunnel ipsec-map2 out
no shutdown

速度については、所詮フレッツなので負荷をかけるには至りませんでした。
iperfでの測定に限って言えばVPN経由のほうが速度がでるときもありました。

いずれにせよ、省スペースでらくらく使えるルータとしてはアリだと思います。消費電力も小さいですし。

0 件のコメント:

コメントを投稿